Honda NC750/700 Page

ON THIS PAGE:

4CS Power Circuit Kit

4CS Leads and Accessories

Aux Harness, Relay, and Fuse

6P Splitter

Aux Power Leads

6P Connector for DIY

Brake/Tail Adapters

4CS Fusepanel Kit

This kit was developed for the 2018 NC750X, other models will also fit if they have the 6P aux power connector on the left side below the frunk. Please contact us if you have a similar model and are unsure. We would love to know all models this Kit will fit. This Kit uses the 6P aux power connector to switch its relay. With our splitter you can still use the connector for the Honda aux power adapter or other purposes. These bikes have limited area to mount a fuse panel, but this kit makes installation easy, mounting everything in the battery compartment accessible in the frunk. If you are now using the stock aux power connector or need to in future, we offer a 6P splitter further down this page so you can plug in this kit and the stock adapter. We are making a simple 6P adapter, as well.

FEATURES:

- 1 Unswitched circuit for battery charging, and power when bike is off

- 3 switched circuits go on and off with the bike

- each circuit has a 10A max capacity, total kit max capacity is 30A

- all components are sealed

- mating sealed connectors are included, extras available below

- fuseholders can each hold an extra fuse

- all wires and sheathing high temp type

- extensions, leads, and splitters available below

- 4 plugs are now included so you can make caps for two circuit outputs you aren’t using

Extra Connectors for CS Kits:

Male connectors are included with each CS kit to install on your accessory’s wires, order more below to have spares, make up your own extensions and splitters, etc.

2 Position .090 Waterproof MT Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Small size tough plastic housing with inner seal. Seals on each wire. Click below to buy: 2P090WP-MT Connector Set  $3.95 ea Quantity: Male Half $2.49 ea Quantity: Female Half $1.95 ea Quantity:

Crimper for sealed connector terminals:

The Hozan P-706 does a pro job on these types, go here to buy. This is a great tool for a home shop, most connectors on modern bikes are this type.

You don’t need a crimper to install these. You can pinch and solder if you know how to solder. I have a page about crimping and soldering here.

CS Sealed  Leads and Extensions

Various pre-finished leads of the highest quality are available for running your circuit wires from the CS Kit under the seat to up front to power a socket, SAE, aux lights, or other devices. Leads are available for a variety of power socket connections to plug in directly. Extensions can be used where you install the male connectors that come with the CS Kit on the wires of your device (like an automotive socket with pigtails), everything then plugs together. Wires, connectors, and sheathing are high temp, highest quality, Japan made by Eastern Beaver.

CS Extensions

- pre-made solutions to connect from the CS Kits to your accessory.

- male connector on one end and a female on the other end, male plugs into a CS Kit output connector - then you can use one of the included (comes with every CS Kit) male connectors on your accessory wires to complete the circuit - give you a modular way to connect your circuits

CS Kit Leads - these leads have specific terminating connectors for different accessories

CS Kit Leads with SAE Plug 2 Prong SAE Plug for battery chargers, etc., WITH 16 AWG wire. (NOW WITH SAE CAP) CS Kit Leads Sealed (SAE) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (SAE) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (SAE) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (SAE) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (SAE) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (SAE) 160 cm (64”) $18.95 Quantity: CS Kit Leads with T-Connector 2 Prong T-Connector for Powerlet and Hella type Socket - with 18 AWG wire CS Kit Leads Sealed (TCON) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (TCON) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (TCON) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (TCON) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (TCON) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (TCON) 160 cm (64”) $18.95 Quantity: CS Kit Leads with 1/4” Pushons 2 1/4” Sheathed Push-on Receptacles for Automotive Sockets etc. - with 18 AWG wire CS Kit Leads Sealed (.250”) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (.250”) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (.250”) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (.250”) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (.250”) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (.250”) 160 cm (64”) $18.95 Quantity:

2P SAE Now with Cap 2P T Connector for Sockets 2 Sheathed Plated 1/4” Pushons

CS Splitters - NOTE: all CS Splitters are now a more compact 15 cm (6 in)

These splitters are designed to allow you to power even more accessories from your CS Kit.

All splitters are 15 cm(6”) long.

They are made of high quality Yazaki wire of 0.75 sqmm (18 AWG), with high temp flexible sheathing.

You can order any of the combinations below and more. Pick the connectors you need for your accessories.

The Splitters below are examples of possible choices, and plug into the CS Kit Outputs, or the CS Kit Extensions above.        

Two CS Kit outputs - use to split one CS Kit output to two. One T-Connector for Powerlet type sockets, and one set of insulated push on 1/4” females - use to connect one CS Kit output to two different sockets. Two sets of 1824 Posi-Locks for the ultimate in easy installations. Also use when you have devices with pigtail wires. Another output option (not shown) is a high quality SAE connector with cap. CS Kit Sealed Splitter $19.95 Option 1 Posi-Locks Sealed Connector T-Connector SAE Plug Push-Ons Option 2 Posi-Locks Sealed Connector T-Connector SAE Plug Push-Ons Quantity:

Lead Install Page

6P Aux Harness, Relay, and Fuse

This harness duplicates (betters) Honda’s at a lower price. We make them ourselves. The relay and fuse fit into the open slots in the bike’s relay/fuse panel. You can plug in Honda’s Heated Grips, Power Socket, and Fog Lights. Or you can wire in your own devices using the included mating connectors. The relay and fuse are necessary to activate the harness. Wire outputs sizes are 18 AWG.

Better than factory and cheaper - comes with mating connectors. 35A ISO Relay by Panasonic ISO Relay 35A -  $9.95 Quantity: 7.5A Low Profile ATM Fuse 7.5A Low Profile ATM Fuse $0.95 Quantity: NC700/750 Aux. Power Harness $29.95 Quantity: NOTE: In order to make this splitter active you must also buy the relay and fuse shown here, and install them in your bike as shown on the right. Pic above show relay and fuse location.

6P Aux Connector with Leads

This connector plugs into the stock 6P aux power connector and gives you 36” (92cm) of high temp 16 AWG wire with high temp sheathing. This connector is fused on the bike aux power fuse. This is the DIY simple solution to power your GPS, charge your phone, etc. NOTE: This harness needs the relay and fuse above to activate it.

NOW with 3 wires, 1 switched power (blue), 1 HI beam switched power(white), and ground (black).

6P Aux Connector Splitter

This splitter plugs into the stock 6P aux power connector and gives you two connectors, so you can connect two 6P aux connectors or our 4CS and the stock aux adapter.

6P Aux Connector and Extras

These units plug into the stock brake/tail light connector For the hardcore DIYer.

6 Position .090 Waterproof Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Tough plastic housing with inner seal, plus seals on each wire. Click below to buy: 6P090WP-HM Set $7.49 ea Quantity: Male Half $4.49 ea Quantity: Female Half $2.95 ea Quantity:

Sealed HM and MT Pins and Seals Terminals also fit HW sealed series. For HW seals see the DL series. Click below to buy: HM/MT/HW Male Terminal  $0.14/EA Quantity: HM/MT/HW Female Terminal  $0.14/EA Quantity: HM/MT Seal $0.09/EA Quantity: HM/MT Plug  $0.12/EA Quantity:

Brake/Tail Adapters ( 2016 - 2020 )

These units plug into the stock brake/tail light connector to add aux lighting or even a brakelight modulator (V2).

Power your top box lighting, your aux brake light, and more.

Features: 24” (61cm) high temp wire and high temp sheathing

Version 1 - straight takeoffs, NOT for brakelight modulators

Brake/Tail Adapter for NC750 Version 1 $18.95

(black wire is ground, yellow is tail light, red is brake light)

Version 1 - extra wire for brake in and out, for brake light modulators

Brake/Tail Adapter for NC750 Version 2 $20.95

(black wire is ground, yellow is tail light, red is brake light power to modulator, purple(yellow) is brake light)

Brake/Tail Adapter Version 1 ( 2021 -  Please check your tail light connector. Earlier models had a smaller 3 pin connector.  )

These units plug into the stock brake/tail light connector to add aux lighting or use as a source of switched power for low current devices )

Power your top box lighting, your aux brake light, and more.

Features: 24” (61cm) high temp wire and high temp sheathing

NOT for brake light modulators

Brake/Tail Adapter V1 for NC750 2021- $18.95

 

Brake/Tail Adapter Version 2 ( 2021 -  Please check your tail light connector. Earlier models had a smaller 3 pin connector.  )

This units plug into the stock brake/tail light connector to allow the addition of a brake light modulator
Red is the brake light signal from the bike to the modular ( usually power in )
Black is ground
Blue is tail light
Purple is brake light input to tail/brake light ( output from modulator )
Effectively this cable allows you to wire your modulator between the bike wiring and the brake light without modifying your bikes OEM wiring.

Features: 24” (61cm) high temp wire and high temp sheathing

For brakelight modulators

Brake/Tail Adapter V2 for NC750 2021- $20.95