Centech AP-1 Wiring Kits (also fit BlueSea and others)

Click here for the AP-1 Details Page with more photos and info.

Click here to see AP-1 Installation instructions and fuse panel installation photos.

Before Ordering: You must first figure out where you'll mount your fuse panel on your bike. Most important is to find a location where it fits with some room to wire into it. You should be able to access the fuse panel later if you blow a fuse. The fuse panel should be sheltered from rain and dirt. Ideally, it should be mounted somewhere between the battery and the front of the bike, since that's likely where your accessories will be. If necessary, the fuse panel can be mounted in the tail of the bike if that's the only place you can put it. However, when using a rear location, you'll need to run long wires up front to your accessories. In that case, you might consider my wire looms which run several wires in one sheathing.

Heavy Duty 30A Fusebox Leads Only (no fusebox)

If you want your fuse panel powered at all times, this is the simple solution.

Measure from POS battery post to fusebox and add a few extra inches. Add more length according to routing around frame, etc. You can of course shorten the fusebox ends to your exact requirements. Includes two 30A fuses and cable ties.

Kit length is based on distance from the Positive battery lead end to the end of the fusebox wires.

18"(40cm) $12.95 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length 24"(61cm) $13.95 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length

30"(76cm) $15.45 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length 36"(91cm) $16.95 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length

42"(107cm) $18.45 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length 48"(122cm) $19.95 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length

54"(137cm) $21.45 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length 60"(152cm) $22.95 Battery Lead Option NEG Lead 6" (15 cm) Longer than POS POS Lead 6" (15 cm) Longer than NEG Both Leads Same Length

If you want a pair of 5.5 mm ring terminals installed (for your fuse panel), click below:

2 5.5 mm Ring Terminals Installed $3.00

Installation of terminals includes factory crimping and Sumitube shrink tube covering.

These terminals and more are available on my Terminals Page for less, if you want to DIY.

The AP-1 comes with extra non-insulated terminals. See here for how to crimp and solder the AP-1 terminals.

Heavy Duty 30A Fusebox Relay Kit Only (no fusebox)

No matter what fuse panel you have, this Kit will allow its power to be switched on and off with the bike.

Measure from positive battery post to fusebox and add a few inches. Add more length according to routing around frame, etc. Kit lengths below are the overall total length from battery POS lead to fuse panel. Switching leads can be shortened according to your needs. Includes two 30A fuses for the main fuseholder.

The relay is located 10" (25 cm) from the end of the positive battery lead.

Battery Lead Lengths - the NEG battery lead by default is 6" (15 cm) longer than the POS lead as shown above. If you'd like a different battery lead arrangement, order the MetriPack fuseholder option below.

18"(40cm) $29.95 24"(61cm) $30.95 30"(76cm) $32.45 36"(91cm) $33.95

42"(107cm) $35.45 48"(122cm) $36.95 54"(137cm) $38.45 60"(152cm) $39.95

KIT OPTIONS:

Protective Diode Option: A protective diode can be ordered inline on the ignition switched lead, preventing reverse EMF flow back to the bike. The diode is inserted as shown here. This is highly recommended for CANBus bikes.

Click below to add the diode feature:

Protective Diode in Switching Wire Option $5.95

Extra Long Switching Lead Option: 48" (122 cm) long switching lead instead of the stock 24" (61 cm) lead. Great for going all the way up to the parking light from the rear of the bike.

Extra Long Switching Lead Option $1.95

Metri-Pack Fuseholder Option: If you'd like a Kit with more custom options then choose the Metri-Pack Fuseholder Option below.

This optional fuseholder will replace the standard fuseholder on this Kit.  Price $3.95 (This price only with Kit) Figure out where it's best to mount your fuseholder and relay and order your Kit just right for your requirements. See some Kits with the MP Fuseholder here. Select Lengths: Fuseholder Distance from Battery 4 in (10 cm) from Bat POS 6 in (15 cm) from Bat POS 8 in (20 cm) from Bat POS 10 in (25 cm) from Bat POS Relay Distance from Fuseholder 4 in (10cm) from fuseholder 6 in (15 cm) from fuseholder 8 in (20 cm) from fuseholder 10 in (25 cm) from fuseholder Metri-Pack Fuseholder

5.5 mm Ring Terminal Installation Option:

If you want a pair of 5.5 mm ring terminals (fits AP-1 or Bluesea) installed on the leads, click below:

Note: I am now using high quality open barrel brass ring terminals that don't need soldering. 2 5.5 mm Ring Terminals Installed $3.00

Installation of terminals includes factory crimping and Sumitube shrink tube covering.

These terminals and more are available on my Terminals Page, if you want to DIY.

The AP-1 comes with 2 5.5 mm non-insulated terminals. See here for how to crimp and solder this type of terminal.