Fusepanel Wiring Kits

Click here to see fusepanel installation instructions and photos.

Before Ordering: You must first figure out where you'll mount your fuse panel on your bike. Most important is to find a location where it fits with some room to wire into it. You should be able to access the fuse panel later if you blow a fuse. The fuse panel should be sheltered from rain and dirt. Ideally, it should be mounted somewhere between the battery and the front of the bike, since that's likely where your accessories will be. If necessary, the fuse panel can be mounted in the tail of the bike if that's the only place you can put it. However, when using a rear location, you'll need to run long wires up front to your accessories. In that case, you might consider my wire looms which run several wires in one sheathing.

30A Single Circuit Fusepanel Leads Only - AP-1, Bluesea, * Fuzeblock

If you want a fuse panel powered at all times, this is the simple solution.

Single circuit fusepanels do NOT have both switched and unswitched circuits. This Kit will allow all circuits to be always on with this type of fusepanel.

Measure from closest battery post to fusepanel and add a few extra inches. Add more length according to routing around frame, etc. Includes two 30A ATM fuses and cable ties.

Choose the length of leads you require and a battery lead option.

18"(40cm)  $12.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 24"(61cm)  $13.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

30"(76cm)  $15.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 36"(91cm)  $16.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

42"(107cm)  $18.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 48"(122cm)  $19.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

54"(137cm)  $21.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 60"(152cm)  $22.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

Made from 12 AWG high temp wire and tough high temp sheathing.

M5 Ring Terminal Installation Option:

If you want an extra pair of M5 mm ring terminals and shrinktube so you can trim the lengths if necessary, click below: 2 M5 mm Ring Terminals and Shrinktube $1.49 These terminals and more are available on my Terminals Page, if you need spares. The M5 ring terminals on this Kit will fit the AP-1 or Bluesea fuse panels' input  posts.

Fuzeblocks FZ-1 Leads

Basically the same leads as above but with no ring terminals. Includes a 54" (137 cm) switching lead and Posi-Tap.

Choose the length of leads you require, battery lead option.

18"(40cm)  $14.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 24"(61cm)  $15.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

30"(76cm)  $17.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 36"(91cm)  $18.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

42"(107cm)  $20.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 48"(122cm)  $21.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

54"(137cm)  $23.45 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder 60"(152cm)  $24.95 Battery Lead Option NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length Choose a Fuseholder ATM Metri-Pack 280 Fuseholder ATF Metri-Pack 630 Fuseholder

30A Single Circuit Fusepanel Relay Kits - AP-1, Bluesea, etc.

Single circuit fusepanels do NOT have both switched and unswitched circuits. This Kit will allow all circuits to be switched on and off with the bike on this type of fusepanel.

Measure from battery post closest to fusebox and add a few inches. Add more length according to routing around frame, etc. Kit lengths below are the overall total length from the battery post closest to fuse panel.  Switching leads can be shortened according to your needs. Includes two 30A fuses for the main fuseholder.

The relay is located 10" (25 cm) from the end of the positive battery lead.  You can order both leads the same length in the options below.

Battery Lead Lengths - the NEG battery lead by default is 6" (15 cm) longer than the POS lead as shown above.

18"(40cm)  $26.95 24"(61cm)  $27.95 30"(76cm)  $29.45 36"(91cm)  $30.95

42"(107cm)  $32.45 48"(122cm)  $33.95 54"(137cm)  $35.45 60"(152cm)  $36.95

FREE - Battery Lead Configuration Option: If you'd like a Kit with the POS battery lead longer than the NEG, or both leads the same length, indicate your choice here. There is no charge for this option but of course you must be buying a Fusepanel Relay Kit above.

Alternate Battery Leads Configuration  FREE Choose NEG Lead +6 in(15 cm) POS Lead +6 in(15 cm) Both Leads Same Length

FREE - Switching Lead Posi-Tap Choice: I now give you a choice of Posi-Tap to suit different wire sizes. Some bikes, especially CanBUS bikes have very small wires. The parking light wire definitely needs a PTA2024 it's so small. There is no charge for this option but of course you must be buying a PC-8 and Relay Kit above. See the Posi Products Page for info about Posi-Taps and their sizes.

The Kits normally come with the PTA1416 which will fit most bikes but it's nice to have the right size.

Buy few sizes at the above link and make sure you have one that fits just right.

Switching Lead Posi-Tap Choice FREE (Choose 1 ONLY) Choose PTA1800 PTA2022

30A Dual Circuit Fusepanel Relay Kits - PC-8 or AP-2 Installation Page Here.

This Kit is for dual circuit fuse panels with both switched and unswitched circuits. Regular Kits have a Posi-Tap on the switching lead. This photo shows the VStrom version. (also fits SV models)

Measure from positive battery post to fusebox and add a few inches. Add more length according to routing around frame, etc. Kit lengths below are the overall total length from the battery post closest to fuse panel.  Switching leads can be shortened according to your needs. Includes two 30A fuses for the main fuseholder.

The relay is located 10" (25 cm) from the end of the positive battery lead. The MetriPack fuseholder option allows different positioning and lead lengths to the battery.

Battery Lead Lengths - the NEG battery lead by default is 6" (15 cm) longer than the POS lead as shown above. You can order both leads the same length in the options below.

Switched circuits are turned off when the bike is shut down. An unswitched circuit is always hot.

18"(40cm)  $29.95 24"(61cm)  $30.95 30"(76cm)  $32.45 36"(91cm)  $33.95

42"(107cm)  $35.45 48"(122cm)  $36.95 54"(137cm)  $38.45 60"(152cm)  $39.95

Kit length is from battery POS to fuse panel.

See Options for this Kit further down the page.

50A Dual Circuit Fusepanel Relay Kits - PC-8 or AP-2 Installation Page Here.

This Kit uses two main fuseholders to give you a total capacity of 50A. 12 AWG input wire is used on the switched circuits for 30A, and a 14 AWG input wire is used on the unswitched circuits for 20A. The main ground wire is 10 AWG. An 18" (40cm) Kit is shown above. This Kit also comes with two 30A and two 20A fuses for the main fuseholders.

Kit length is from battery POS to fuse panel.

Fuse Panel Relay Kit Options (for all Relay Kits on this page)

FREE - Battery Lead Configuration Option: If you'd like a Kit with both leads the same length, indicate your choice here. There is no charge for this option but you must be buying a Dual Circuit Fusepanel Relay Kit above. By default, the NEG battery lead is 6" (15 cm) longer.

Alternate Battery Leads Configuration  FREE

FREE - Switching Lead Posi-Tap Choice: I now give you a choice of Posi-Tap to suit different wire sizes. Some bikes, especially CanBUS bikes have very small wires. The parking light wire definitely needs a PTA2024 it's so small. There is no charge for this option but of course you must be buying a PC-8 and Relay Kit above. See the Posi Products Page for info about Posi-Taps and their sizes.

The Kits normally come with the PTA1416 which will fit most bikes but it's nice to have the right size.

Order a few sizes and make sure you have one that fits just right.

Switching Lead Posi-Tap Choice FREE Choose PTA1800 PTA2022

KIT EXTRA CHARGE OPTIONS - available for all Relay Kits on this page - NOT for Fusepanel Leads:

Protective Diode Option: A protective diode can be ordered inline on the ignition switched lead, preventing reverse EMF flow back to the bike. The diode is inserted as shown here. This is highly recommended for CANBus bikes.

Protective  Diode in Switching Wire Option $5.95

Extra Long Switching Lead Option:  56" (142 cm) long switching lead instead of the stock 24" (61 cm) lead. Great for going all the way up to the parking light from the rear of the bike. Or order a Posi-Lock PL1416 and extend the lead yourself.

Extra Long Switching Lead Option $2.95

Extra Terminals, Sheath and Shrinktube: If you have ordered your Kit a bit long because you're unsure of the exact length needed,  these optional parts will  allow you to cut the fuse panel leads shorter and install new terminals.

Single Circuit 2 Terminals and Shrinktube $1.95

Dual Circuit 3 Terminals, Sheath and Shrinktube $2.95