Honda CRF450 Page

4CS Fusepanel Kit

This kit was developed for the 2018 CRF450, other similar models may also fit if they have the 2P aux power connector on the left side above the front of the motor. Please contact us if you have a similar model and are unsure if this Kit will fit. We would love to know all models this Kit will fit. This Kit uses the 2P aux power connector to switch its relay. With our splitter you can still use the connector for the Honda aux power adapter or other purposes. These bikes have limited area to mount a fuse panel, but this kit makes installation easy, mounting everything near the battery compartment under the seat.

4CS Sealed for CRF450  $64.95

FEATURES:

- 1 Unswitched circuit for battery charging, and power when bike is off

- 3 switched circuits go on and off with the bike

- each circuit has a 10A max capacity, total kit max capacity is 30A

- all components are sealed

- mating sealed connectors are included, extras available below

- fuseholders can each hold an extra fuse

- all wires and sheathing high temp type

- extensions, leads, and splitters available below

- 4 plugs are now included so you can make caps for two circuit outputs you aren’t using

- a splitter is available if your bike’s 2P aux power connector is in use for something else

Aux Power Splitter

If your bike’s connector is in use, you will need this splitter to connect our 4CS Kit’s switching leads.

(DOES NOT USE THE CS CONNECTORS, GO HERE TO THE 2P CONNECTOR TO THIS SPLITTER AND LEADS)

Aux Power Leads

Plugs into bike connector or splitter above

Extra Connectors for CS Kits:

Male connectors are included with each CS kit to install on your accessory’s wires, order more below to have spares, make up your own extensions and splitters, etc.

2 Position .090 Waterproof MT Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Small size tough plastic housing with inner seal. Seals on each wire. Click below to buy: 2P090WP-MT Connector Set  $3.95 ea Quantity: Male Half $2.49 ea Quantity: Female Half $1.95 ea Quantity:

Crimper for sealed connector terminals:

The Hozan P-706 does a pro job on these types, go here to buy. This is a great tool for a home shop, most connectors on modern bikes are this type.

You don’t need a crimper to install these. You can pinch and solder if you know how to solder. I have a page about crimping and soldering here.

CS Sealed  Leads and Extensions

Various pre-finished leads of the highest quality are available for running your circuit wires from the CS Kit under the seat to up front to power a socket, SAE, aux lights, or other devices. Leads are available for a variety of power socket connections to plug in directly. Extensions can be used where you install the male connectors that come with the CS Kit on the wires of your device (like an automotive socket with pigtails), everything then plugs together. Wires, connectors, and sheathing are high temp, highest quality, Japan made by Eastern Beaver.

CS Extensions

- pre-made solutions to connect from the CS Kits to your accessory.

- male connector on one end and a female on the other end, male plugs into a CS Kit output connector - then you can use one of the included (comes with every CS Kit) male connectors on your accessory wires to complete the circuit - give you a modular way to connect your circuits

CS Kit Leads - these leads have specific terminating connectors for different accessories

CS Kit Leads with SAE Plug 2 Prong SAE Plug for battery chargers, etc., WITH 16 AWG wire. (NOW WITH SAE CAP) CS Kit Leads Sealed (SAE) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (SAE) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (SAE) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (SAE) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (SAE) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (SAE) 160 cm (64”) $18.95 Quantity: CS Kit Leads with T-Connector 2 Prong T-Connector for Powerlet and Hella type Socket - with 18 AWG wire CS Kit Leads Sealed (TCON) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (TCON) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (TCON) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (TCON) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (TCON) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (TCON) 160 cm (64”) $18.95 Quantity: CS Kit Leads with 1/4” Pushons 2 1/4” Sheathed Push-on Receptacles for Automotive Sockets etc. - with 18 AWG wire CS Kit Leads Sealed (.250”) 15 cm (6”) $10.95 Quantity: CS Kit Leads Sealed (.250”) 30 cm (12”) $11.95 Quantity: CS Kit Leads Sealed (.250”) 60 cm (24”) $12.95 Quantity: CS Kit Leads Sealed (.250”) 90 cm (36”) $14.95 Quantity: CS Kit Leads Sealed (.250”) 120 cm (48”) $16.95 Quantity: CS Kit Leads Sealed (.250”) 160 cm (64”) $18.95 Quantity:

2P SAE Now with Cap 2P T Connector for Sockets 2 Sheathed Plated 1/4” Pushons

CS Splitters -NOTE: all CS Splitters are now a more compact 15 cm (6 in)

These splitters are designed to allow you to power even more accessories from your CS Kit.

All splitters are 15 cm(6”) long.

They are made of high quality Yazaki wire of 0.75 sqmm (18 AWG), with high temp flexible sheathing.

You can order any of the combinations below and more. Pick the connectors you need for your accessories.

The Splitters below are examples of possible choices, and plug into the CS Kit Outputs, or the CS Kit Extensions above.        

Two CS Kit outputs - use to split one CS Kit output to two. One T-Connector for Powerlet type sockets, and one set of insulated push on 1/4” females - use to connect one CS Kit output to two different sockets. Two sets of 1824 Posi-Locks for the ultimate in easy installations. Also use when you have devices with pigtail wires. Another output option (not shown) is a high quality SAE connector with cap. CS Kit Sealed Splitter $19.95 Option 1 Posi-Locks Sealed Connector T-Connector SAE Plug Push-Ons Option 2 Posi-Locks Sealed Connector T-Connector SAE Plug Push-Ons Quantity:

Lead Install Page