|
Royal Enfield Himalayan
|
 |
- PC-8 Specifications and Features:
- - 4 threaded insert nuts provide case mounting and fuse panel installation mounting points
- - comes with an assortment of ATM fuses, one for each output circuit and a few extras
- - 8 hot + outputs (2 unswitched circuits, 6 switched circuits)
-
- Switched circuits are turned off when the bike is shut
down. Two unswitched circuits are always hot - can be used for charging the battery
- - 8 ground outputs - much better to ground your auxiliary circuits here than on a bike’s frame
- - maximum fuse panel capacity
40 Amps (20A/20A - switched/unswitched)
- - maximum circuit capacity 20 Amps (15A continuous)
- - maximum output wire size 12 AWG (3 sqmm)
- - all hardware is stainless steel (except input posts which are tin plated steel)
- - black satin polycarbonate cover makes unit splash-proof yet allows it to breathe and stay cool
- - cover mounting tabs on each end can be broken off or left on, depending on mounting choice
- - simple robust design means no overheating and no problems with vibration
- - I designed this fuse panel with ease of mounting a priority. Therefore there are many mounting options: Dual Lock on back of case, fine threaded screws from back of panel, self tapping screws from inside through PCB inserts to panel, or nuts and screws on the case mounting ears at each end of the case.
PC-8 Fuse Panel Kit - 8
output for system
4 Circuit Solution Sealed Kit - four
output system
Tail Light Splitter
- Switched output for Fuse
Boxes or lower power accessories.
PC-8 Fuse Panel Kit
Complete plug and play kits, with all the wiring, a 40A relay, fuses, a PC-8 fuse panel, and more.
Battery Connect Complete Kit
|
PC-8 and Relay Kit for
Himalayan $99.95
|
|
Installation Note: This kit uses the
tail light connector at the rear of the bike under the
passenger seat. The kit is designed to be installed under
the passenger seat. The relay and fuse holders on one side
and the PC-8 on the other ( left side when seated on the
bike ) You may need to move anything you have stowed
there as the kit takes up most of the under seat space.
4 Circuit Solution Sealed Kit
This Kit is for power needs up to
40A total current, split between 4 outputs ( 2 switched and
two un-switched ) on the Kit. You can split the
outputs further with our CS splitter cables to achieve more
outputs, for lower current devices ( lower section of
this page .
This Kit has two main fuses. You can charge the battery through the un-switched circuit which is always hot. The switched circuits are switched by the relay to be on only when the bike is on.
Two switched outputs are provided, controlled by a 20A relay and a main
fuse holder of 20A max. Switched outputs are max 10A each. These switched outputs are great for most of your accessories,
mobilel phone, GPS etc, even heated clothing can be powered.
Two un-switched output
are provided direct from battery using its own fuse, with max capacity of
10A each or 20A on one, if only one circuit used. The bike battery can be charged with this circuit.
The relay is a very compact 20A unit with extra protection shrunk over it. Mating connectors and fuses are included. Extra connectors and parts are available on the Accessories Page.
Leads, extensions, and splitters to plug into the 3CS Sealed are now available on the Accessories Page.
Kit with Battery Connections (also available to hookup to our Powerlink battery leads)
Himalayan 4CS
|
4CS for
Royal Enfield Himalayan $59.95
|
|
Installation Note: This kit uses the
tail light connector at the rear of the bike under the
passenger seat. The kit is designed to be installed under
the passenger seat. The relay and fuse holders on one side
and the PC-8 on the other ( left side when seated on the
bike ) You may need to move anything you have stowed
there as the kit takes up most of the under seat space.
Tail Light Splitter
This cable allows you to
take a switched output from the rear tail/license plate
light feed. Useful for triggering switched outputs on
the PC-8 or other fuse boxes. It could also be used for
low power accessories. We recommend under 3A loads on
this splitter ( due to tail light/license plate light
already drawing current on this circuit ).
.
|
Tail/License
Plate Light Splitter for
Himalayan $19.95
|
|
Accessories:
|
Dual Locks Strips - Two pairs of mating 4” (10 cm) Dual Lock strips. Great for many other projects too, this material has 5 times more holding strength than regular Velcro. Strips have excellent adhesive on the back. Clean surfaces with alcohol first.
|
|
|
|
2 Sets 4 Inch 3M Dual Lock Strips $2.95
|
|
|
|
More PC-8 mounting accessories
click here.
( lower section of page )
|
