Powerlink System

On This Page =>

Jump Start System

Splitter

Buddy Leads

Female to Clips Adapter

High Power Socket Leads

High Power Horn Kit

Basic Jump Start System - This is a system with jump starting as its primary purpose. You can jump start from bike to bike to get going again. This Kit uses 10 AWG (5 sqmm) wire and a heavy duty sealed connector. You carry the jumper leads on the bike, leaving the battery leads in place with the cap. Many others things can plug into the Battery Leads - aux fuse panels, special high current horns, sockets, and other devices The clips we use are all stainless, made in Japan, and perfect for bikes with limited clearance around the battery. They’re compact and easy to store too.

Disclaimer - this system is not designed for cars or vehicles with high starter currents. It is designed for occasional use for motorcycles and other small vehicles. We are not responsible for damages that might be caused by using this system. We build this system from the highest quality components using excellent crimping and assembly. All wire and sheathing are high temp type.

powerlink

 

Available in parts, choose your lengths:

Jumper Leads:

36” (91cm) $29.95

Quantity:

48” (122cm) $34.95
Quantity:

Cap

 $5.95

Quantity:

Battery Leads:

6” (15cm) $14.95

Lead Lengths
Quantity:

12” (31cm) $16.95
Lead Lengths
Quantity:

18” (46cm) $19.95
Lead Lengths
Quantity:

24” (62cm) $21.95
Lead Lengths
Quantity:

Battery Lead Lengths - the shortest lead is the length listed, the longer lead will be 6 inches longer. When both leads are the same, both are the length listed. 6” leads shown below, POS +6”

plbl6-p6


Powerlink System Add-Ons Because you’re only jump starting bikes in emergencies, the Powerlink connection to battery can be used to power all kinds of things on the bike. If you need to jump start, unplug the main connector from the battery leads and plug in the Jumper Leads. In fact when jump starting it’s best to turn off or is possible disconnect all accessories for maximum battery power and to avoid any electronics damage with current surges etc while jump starting. The Powerlink connection can include a fuse panel on one side of the splitter, and still have capacity for a high power socket on the other side of the splitter. You can also charge through the Powerlink or splitter. You could power a high power horn on one side, your fusepanel on the other side. There’s all kinds of possibilities with the Powerlink System.

We now have an option with our 3 Circuit Solution and our PC-8 fusepanel Kits for a Powerlink main connector that will plug into the Powerlink Battery Leads or Splitter to minimize battery connections.

High Power Horn Kits are now available to plug into the Powerlink System. This makes it easy to power your high power horn directly from the battery, while keeping your fusepanel separate, using the Powerlink Splitter below.

 


Powerlink Splitter

This is a splitter to allow you two power/ground take-offs from your Powerlink Battery Leads. This splitter is made with 12 AWG(3 sqmm) wires to give you max capacity of 30A on each connector. Total power available is 35A. You can add a Powerlink Cap on an unused connector. This is an extremely high quality hand assembled unit.

PL-splitter

Powerlink Splitter $34.95

Quantity:


Powerlink Jump Start Buddy Leads:

This is an alternative to the leads with clips on one end. Made with the same 10 AWG wire and high temp sheath and connectors. With these leads you get a male connector on each end. You and a buddy can enjoy plug and play jumpstarting if you both have the Battery Leads installed. Both can use the Battery leads full time with PC-8s etc and have quick connect no fuss no muss jump start ability bike to bike. Add the short Female to Clips adapter and you can also jump start other bikes.

Jump Start Buddy Leads:

36” (91cm) $24.95

Quantity:

48” (122cm) $29.95

Quantity:

 

Female to Clips Adapter

12” (31cm) $22.95

Quantity:

24” (62cm) $24.95

Quantity:

PL-buddyjumper
qlw-femtoclips


The 2P heavy duty sealed connectors are the Furukawa QLW 250” Rated at 35A - see the full QLW series here.

 2 Position .250 Sealed Waterproof Connector

S size fits wires to 3 sqmm (12 AWG).

L size fits wires to 5 sqmm (10 AWG).

Complete with terminals and seals.

2p-qlw250

QLW 2P250-Male-S  $5.95 ea

Quantity:

QLW 2P250-Male-L  $5.95 ea

Quantity:

QLW 2P250-Female-S  $5.95 ea

Quantity:

QLW 2P250-Female-L  $5.95 ea

Quantity:

 

Powerlink 20A Socket Leads: coming soon

Powerlink 20A High Power Horn Kit: Now available here.