All New 4 Circuit Solution Sealed (4CS-S) Kits and Components

NOTE: We have reworked all the 4 Circuit Solution Sealed models with all new modular fuse holders that hold extra fuses, and a neater, more compact design. At the same time we’ve increased battery lead length to easier fit all bike models. The 4CS Kits on this page are generically designed for all bikes, however, please note that we have bike specific kits for some popular bikes, see here. My apologizes for any errors on this page, or incorrect pictures. We have just introduced the 1, 2 and 4 Circuit Solutions, and discontinued the 3CS.

– These CS Kits are all part of a modular system that uses the same connectors and parts.

– We make various compatible extensions, leads, and splitters further down this page.

Battery Connections plug 4CS Sealed

Shown kit, with Battery Connections (also available to hookup to our Powerlink battery leads)

$59.95 – $65.95

4 Circuit Solution Sealed

This Kit is for medium power needs up to 35A total current on the Kit. (40 cm Kit shown, a longer kit is available) This Kit has two main fuseholders. The black is for the switched circuits which also each have a separate fuseholder, the main white fuseholder is for the unswitched circuit. You can charge the battery through the unswitched circuit which is always hot. The switched circuits are switched by the relay to be on only when the bike is on. This Kit uses Sumitomo MT sealed .090” connectors that are easy to work with if crimping or soldering. See here for a crimper for these that will do a professional job on these. The Hozan P-706 is my recommended crimper for sealed types.

Three switched outputs are provided, controlled by a 20A relay and a main fuseholder of 20A max. Switched outputs are max 12A each. These switched outputs are great for most of your accessories, cellphone, GPS etc, even heated clothing can be powered.

One unswitched output is provided direct from battery using its own fuseholder, with max capacity of 15A. The bike battery can be charged with this circuit. This higher power circuit can also power an air compressor or power heated clothing. Or you can use this circuit for a GPS which will stay on and powered when you shut off the bike.

Battery leads are 16 inches long (40cm) on the shortest version, longer kits will be available. The relay is a very compact 20A unit with extra protection shrunk over it. Mating connectors and fuses are included. Also, an extra terminal and seal is included, as well as cable ties. Extra connectors and parts are available on the Accessories Page. Two Positaps are included for the relay switching wire and ground.

Leads, extensions, and splitters to plug into the 3CS Sealed are now available on the Accessories Page.

Kit with Battery Connections (also available to hookup to our Powerlink battery leads)

NEW! - 4CS Sealed all Posi-Lock outputs

4CS Sealed Posi-Lock

Simple no tools install.

$69.96 - $75.95

You get a choice of Battery Connection as shown in the Kits above, or a Powerlink Connection with a 2P QLW sealed male connector to plug into the Powerlink Battery Leads, as shown below.

Kit with Powerlink Kit Connector (battery leads sold separately here, available in different lengths)

Powerlink Option Kits

$14.95 - $29.95

Battery Leads sold separately in different configurations and lengths, see Powerlink Page.

Protective Diode in Switching Wire Option

$5.95

A protective diode can be ordered inline on the ignition switched lead, preventing reverse current flow back to the bike. This is highly recommended for CANBus bikes.

Protective Diode in Switching Wire Option $5.95

2 Position .090 Waterproof MT Connector.

Fits wires from .5mm – 1.25mm (22 – 16 AWG).
Small size tough plastic housing with inner seal. Seals on each wire.

$1.95 - $3.95

Crimper for sealed connector terminals:

The Hozan P-706 does a pro job on these types, go here to buy. This is a great tool for a home shop, most connectors on modern bikes are this type.

You don’t need a crimper to install these. You can pinch and solder if you know how to solder. I have a page about crimping and soldering here.

CS Sealed Leads and Extensions

Various pre-finished leads of the highest quality are available for running your circuit wires from the CS Kit under the seat to up front to power a socket, SAE, aux lights, or other devices. Leads are available for a variety of power socket connections to plug in directly. Extensions can be used where you install the male connectors that come with the CS Kit on the wires of your device (like an automotive socket with pigtails), everything then plugs together. Wires, connectors, and sheathing are high temp, highest quality, Japan made by Eastern Beaver.

CS Kit Extensions

male connector on one end and a female on the other end, male plugs into a CS Kit output connector – then you can use one of the included (comes with every CS Kit) male connectors on your accessory wires to complete the circuit – give you a modular way to connect your circuits

$12.95 - $16.95

CS Kit Leads - these leads have specific terminating connectors for different accessories

CS Kit Leads with SAE Plug

2 Prong SAE Plug for battery chargers, etc., WITH 16 AWG wire. (NOW WITH SAE CAP)

$10.95 - $18.95

CS Kit Leads with T-Connector

2 Prong T-Connector for Powerlet and Hella type Socket – with 18 AWG wire

$10.95 - $18.95

CS Kit Leads with .250″ Spade Connector

2 1/4” Sheathed Push-on Receptacles for Automotive Sockets etc. – with 18 AWG wire

$10.95 - $18.95

CS Kit Sealed Splitter

These splitters are designed to allow you to power even more accessories from your CS Kit.
All splitters are 15 cm(6”) long.

$19.95