PC-4E Fuse Box
The Power Center 4E ( PC-4E ) is an electronic PDM / Fuse box for powering accessories on small vehicles such as motorcycles, ATV’s, snowmobiles, camping trailers etc. It provides 3 switched and 1 battery direct, fused connections. With a rating of 30Amps it is suitable for many applications. All that is needed is a battery connection & a switched input signal. Perfect for getting wires off the battery terminals, and managing power to accessories. You can split outputs using our CS splitter cables. eFuses are reset by power cycling the unit. Super simple operation without the needs for apps or PC software. Built tough, to survive drops or crashes.
Bike specific connection kits available as we add them, or request a specific kit and we will design it.
Specifications And Features
- 4 hot + outputs (1 un-switched circuits, 3 switched circuits)
- Switched circuits are turned off when the bike is shut down. An un-switched circuit is always hot - can be used for charging the battery, heated gear or air pumps.
- 4 ground outputs - much better to ground your auxiliary circuits here than on a bike’s frame
- maximum fuse panel capacity 30 Amps
- 25 Amp max switched. 15A max un-switched ( combination must be under 30 Amp total )
- Direct out 15A continuous rating. Short term max 25A. (Output 1 )
- Switched Outputs: 10A, 10A and 15A ( Output 2, 3, 4 )
- Waterproof & weatherproof, built tough
- PowerLink connection standard.
- No apps or complicated manuals required to operate. Switch off then on to reset a fuse.
- Designed by motorcyclists for motorcyclists.
PC-4E Fuse Box With Wiring Kit
30A PC-4E kits. 3 Switched and 1 Battery Direct output. Complete kit with battery connection and Post-Tap on the Ignition-In line. These kits can be order with a main fuse ( LP JCase fuse holder ) or without, as all outputs are themselves fuse protected. eFuses are reset by power cycling the ignition. The eFuse will check for a short circuit and if none detected, will power the output. The unit has three LED indicating the status of the Switched eFuses. There is also an LED on the Ignition/Trigger input that lets you know that both Power In and Ignition-In are good.
NOTE ON OUTPUT CONNECTIONS:
If ordered with Bullets on the Switched Outputs, then mating Bullet connectors will be provided. If ordered with MT-090 sealed connectors on the outputs, then mating MT-090 connectors & 4 pigtails will be provided. We will also include some MT-090 mating connectors, for those that want to crimp their own connections.
Switching Lead Posi Tap Option
The PC-4E Fuse Box with Install Kit comes with a PTA1800M, you can select a PTA1800M if you have to tap into a thinner wire such as 22AWG ( 0.5mm² ). Otherwise no need for this option. Only one can be ordered per PC-4E Fuse Box With Wiring Kit.
CS Kit Extensions
The PC-4E Fuse Box with Install Kit comes with a PTA1800M, you can select a PTA1800M if you have to tap into a thinner wire such as 22AWG ( 0.5mm² ). Otherwise no need for this option. Only one can be ordered per PC-4E Fuse Box With Wiring Kit.
CS Kit Leads with SAE Plug
PC-4E to SAE connector. Useful for connecting heated gear or battery chargers/ trickle chargers etc.
CS Kit Leads with .250″ Spade Connector
PC-4E to 4mm spade connectors. Useful for connecting accessories.
Suitability & Reliability
Durability:
The PC-4E is built tough. You could drive you car over it and not effect it ( other than scratches ). It is waterproof and weatherproof. Can operate from -20c though to +70c. The PC-4E has built in thermal management, and the Trigger In has a circuit to prevent and noise existing the fuse box, so completely safe on Canbus bikes or with any computer system.
Reliability:
During development, we run the fuse boxes well above their ratings to observe where failures might occur and to do thermal analysis. After correcting any areas of
concern, we run units for weeks on end at elevated temperatures, then subject them to thousands of On/Off cycles. Only when all our test units pass all our tests, do we consider it’s a complete product.